Solid Color Epoxy in Glendora

Solid color epoxy is a single-color, 100% solids coating that goes down seamless and stays that way. There is no chip layer and no pattern to look at, which is the point in a workshop, a storeroom or a small commercial unit where a floor needs to be tough and easy to read rather than decorative.

(310) 270-3256 GET A FREE QUOTE

Why Some Floors Should Be One Color

A decorative floor hides things. Chips and mica pigment disguise dust, small debris and the marks a floor picks up over time, and in a living space that is usually what you want. In a working room it can be the wrong instinct. A plain color shows you a spill, a leak or a dropped fastener straight away, and where things get driven or lifted, seeing the floor clearly is worth more than dressing it up.

It also keeps light where you need it. A pale solid coat bounces a fixture's output back into the room, which in a Glendora workshop or a back-of-house storeroom running one strip light does more than adding another fitting would. And if a section ever needs attention, a single color is far simpler to blend into than a chip blend or a poured pattern.

(310) 270-3256 GET A FREE QUOTE

Covered patio with glossy white epoxy floor adjacent to a lawn and facing a white building with windows.

Shiny, smooth light gray commercial epoxy floor in a large room with windows reflecting outdoors.

Line Striping, Zones and Slip Resistance

Because the base is plain, you can mark it. We stripe traffic lanes, walkways, equipment footprints and keep-clear zones into the system itself, in a contrasting color under the same clear coat, rather than as tape or floor paint laid over the top that gets kicked up inside a season.

Slip resistance goes in the same way, as a fine aggregate broadcast into the coat where it is wanted and left out where it is not. A ramp or a loading area gets it. A showroom floor usually should not, because the texture that stops a boot sliding also holds dirt and makes a mop work harder. That gets decided zone by zone rather than once for the whole floor.

(310) 270-3256 GET A FREE QUOTE

Film Build and What 100% Solids Means

A hardware-store garage kit is mostly water or solvent, and the carrier evaporates. What stays on the concrete is a fraction of what came out of the tin, which is why those floors go thin at the door line and the edges within a year or two. A 100% solids epoxy leaves behind essentially everything that was rolled on, so the film you specify is the film you actually end up with.

That matters because thickness is what buys the floor its life. A home workshop is well served by a standard build. A unit taking pallet jacks, drums or a forklift wants noticeably more, and we say which one you need instead of quoting a single number for every job. It is the largest difference between a floor that runs for a decade and one that starts lifting where the traffic turns.

(310) 270-3256 GET A FREE QUOTE

Empty industrial warehouse space with smooth, glossy light gray epoxy floor and white walls.

Serving Glendora and the Foothill Communities

Rise Coatings installs solid color epoxy across Glendora, from the streets around Glendora Village and Citrus College out to the newer developments climbing toward the foothills, and along the Route 66 corridor where most of the city's small commercial and light industrial units sit. See our work in West Covina, Arcadia and San Marino.

Send the square footage, tell us what the room is used for and whether anything heavier than a car crosses it, and we will quote the build to match. The estimate is free and done on site.

(310) 270-3256 GET A FREE QUOTE

Contact Rise Coatings

Give us a call if you have any questions related to our flooring services, if you would like to inquire about a large flooring project or would like to receive a complimentary onsite estimate.

info@risecoatings.com

+1 (310) 270-3256

8335 Winnetka Ave #178, Winnetka, CA 91306

CSLB # 1108031

Get Your Free Estimate

Thank you for contacting Rise Coatings. One of our representative will get back to you as soon as possible.

Oops! Something went wrong while submitting the form.